New applications of 5G key materials
In the face of the trend of consumer electronics towards thinness and high efficiency, the application of innovative materials in 5G intelligent manufacturing is an urgent challenge. Sil-More Group is a supplier of all-round glue materials. For intelligent display devices, handheld devices, high-frequency optical communication modules, Netcom routers, etc., it provides material applications such as heat conduction and heat dissipation, electromagnetic wave shielding, sensor crystal fixing, lens bonding, component assembly, caulking, insulation packaging, etc. to solve the problem of selecting 5G key materials!
Wireless charging EMI isolation materials
RF-5 SERIES (Sheet Type)
Absorbing sheet material, suitable for various types of thin electronic devices, protects circuit board lines from interference by external signals, applicable frequency range from 1MHz to 10GHz.
Wireless charging EMI isolation materials
WP-RX SERIES (Sheet Type)
The wave-absorbing sheet can effectively enhance the safety performance of the wireless charging module at QI operating frequencies, suitable for frequencies of 125kHz (WPC) and 6.78MHz (A4WP).
Electromagnetic wave shielding
DOWSIL™ EC-6601
Brown, single-component RTV, conductive silicone, electromagnetic shielding effectiveness: 8 dB @ 1 kHz - 8.5 GHz.
Electromagnetic wave shielding
GS-SG6001A
Room temperature curing / FIPG, suitable for 5G base station modules.
SIP signal blocking materials
CS SERIES
Liquid low-viscosity conductive coatings can be applied using manual or automatic spraying, replacing traditional metal shielding/cathodic sputtering, without occupying space on the circuit board and reducing costs.
Cable reinforcement
UV-SIL® 6835-7
UV curing (365NM) PVC/PET/PI joint reinforcement with glass, flexible and bend-resistant, low water permeability.
Cable reinforcement
UV-SIL® 6810
UV curing (365NM) ITO glass is waterproof, flexible, and resistant to bending, with low water permeability.
Thermal Interface Materials
DOWSIL™ TC-3035
Pink, single-component low-temperature curing type, 4 WMK thermal conductive gel, suitable for various interfaces, soft and easy to rework, cures at 60°C, automated dispensing, replaces PAD.
Thermal Interface Materials
DOWSIL™ TC-3015
Pink, single-component low-temperature curing type, 1.8 W/MK thermal conductive gel, suitable for various interfaces, soft and easy to rework, cures at 60°C, automated dispensing, replaces PAD.
EMI Absorbing Material
RF-5 Series (Single Type)
Absorbing sheet material, suitable for various thin electronic devices, protects circuit board lines from interference by external signals, applicable frequency range from 1MHz to 10GHz.
EMI Absorbing Material
AP-40 SERIES (Ink Type)
This is a type of printing ink suitable for printing on chips or PCB circuit boards. It features adhesion and wave absorption properties, and is applicable for frequencies ranging from 300KHz to 18GHz.
IC reinforcement
JC 823-6
Low-temperature curing eliminates the stress generated by drop tests, used for bottom filling.
IC reinforcement
EPO-SIL® UF 1100
High TG can eliminate the stress generated by drop tests, used for bottom filling.
The panel continues.
HM085LB
Hot melt polyurethane resin, black, viscosity: 3000 ~ 5000 (@120℃), curing conditions: 7 DAYS @ RTV, hardness: 75±6(A), good adhesion, can be reworked.
Panel bonding
UV-SIL® 8080-2
Panel assembly, followed by COVER GLASS, curing method: UV (365NM) with low shrinkage rate and good water resistance.
Panel reinforcement
SFX 8368
Fast curing, strong adhesion, non-tin catalyst, compliant with EU standards.
Backlight module
QDE-625 A/B
Quantum dot dispersion glue, low cost and high efficiency, high NTSC > 100, encapsulated as QLED.
Backlight module
QDE-525 A/B
Quantum dot dispersion glue, low cost and high efficiency, high NTSC > 100, encapsulated as QLED.
| Display data rows per page | Search: | |
Rubber material application
|
Product model
|
Feature description
|
| 目前显示第 1 至第 10 个资料列,总计 17 个资料列 | < Previous page Next page> |
Sensor Die Bonding
EP-2015-3-BLACK
Used for dispensing, black insulating adhesive, suitable for SENSOR and IC CHIP die bonding applications.
Sensor Die Bonding
ANE 24054 A3
High adhesion/low temperature curing, suitable for MEMS insulation bonding applications.
Sensor Die Bonding
ACH 44073LV
Solvent-free/low volatile gases, suitable for MEMS conductive die bonding applications.
Insulation packaging
EP-2009-B6
Suitable for bonding/sealing, adhering glass/metal/ceramics, two-stage baking, for printing use.
Insulation packaging
EP-2009-6-H-117
Used for bonding/sealing, adhering LCP/PCB, two-stage baking, for printing.
Insulation packaging
ANE 24054IR
High adhesion / low temperature curing, suitable for bonding LCP / PA.
Insulation packaging
TCI-B-C260
High temperature and low flow characteristics, suitable for LCP bonding.
Voice coil motor conductivity
FP-1725-E4
Curing at low temperatures of 80~100℃, with high adhesion strength and low stress, can replace solder.
Voice coil motor conductivity
ACH 44073LV
Low-temperature curing, solvent-free, low volatile gases, suitable for MEMS conductive die bonding applications.
The lens continues.
UV-SIL® 8090-9-BK
UV curing (365NM/405NM) light shielding and anti-reflective properties, good adhesion to PC/GLASS, and low surface reflectivity in black.
The lens continues.
UV-SIL® 8080-2
UV curing (365NM) high transparency is suitable for lens bonding, with optical lens adhesion having low water resistance and low moisture absorption rate.
Lenses and lens tubes
UV-SIL®2001-1
UV curing (365NM) / MOISTURE low shrinkage rate, high TG, suitable for components and structures sensitive to substrates.
Lenses and lens tubes
UV-SIL® 3001-2
UV curing (365NM) for rapid curing, low shrinkage rate, low CTE, suitable for components and structures sensitive to substrates.
Lenses and lens tubes
EP-13-FL-63
Low-temperature curing, milky white, insulating adhesive, suitable for bonding camera modules and electronic components (LENS), compatible with substrates such as PA and LCP.
The telescope tube is connected to the mount.
UV-SIL® 3014-5
UV curing (365NM) THERMAL (80 degrees/30 MIN) has a fast curing speed, low shrinkage rate, and high Tg.
Mirror base and circuit board assembly
UV-SIL® 3030
Curing method: UV (365NM) THERMAL (80 degrees/30 MIN), adhesive applied to the three edges of the circuit board, fixed with PEI side light (pre-fixing) / bottom thermal curing.
Mirror base and circuit board assembly
EP-2006-SC5-6
Quick curing insulating adhesive, low viscosity/TI, rapid curing at 150°C on a heating plate for 10 seconds.
Mirror base and circuit board assembly
EP-13-LM28NB
Single-component insulating adhesive, curing at low temperature of 70°C for 30 minutes, designed for assembly applications of CCD/CMOS components.
Reinforcement of flexible circuit boards
UV-SIL® 6810
UV curing (365NM) ITO glass has good waterproof and moisture resistance.
Reinforcement of flexible circuit boards
UV-SIL® 6835-7
UV curing (365NM) PVC/PET/PI joint reinforcement with glass, flexible and resistant to bending.
Waterproof LSR rubber strip
SILASTIC™ LC-9930-50
Translucent, dual-component injection molded waterproof adhesive, selectively self-bonding LSR, with good adhesion to PC.
Type C terminal filling
DOWSIL™ 3-6876
Low viscosity heat-curing silicone.
Type C terminal filling
DOWSIL™ SE 9187 L
Excellent liquidity, quick drying, certification: UL94-HB (black, white), used for fixing and reinforcing soft flat cables.
Continue filling the seams.
UV-SIL®3040
Light curing (365NM) / filterability, can filter out light sources below 780NM. Low shrinkage and low moisture absorption rate.
| Display data rows per page | Search: | |
Rubber material application
|
Product model
|
Feature description
|
| 目前显示第 1 至第 10 个资料列,总计 17 个资料列 | < Previous page Next page> |
Continue with stitching and alignment.
UV-SIL® 3026
UV (365NM) thermal (80 degrees/30 minutes) low shrinkage rate, low CTE, used for circuit board three-side dispensing, covered with PEI side light curing (pre-fixing) / bottom thermal curing.
Continue with stitching and alignment.
UV-SIL® 3027
UV (365NM) thermal (110 degrees/30 minutes) high TG, low CTE, used for circuit board three-side dispensing, covered with PEI side light curing (pre-fixing) / bottom thermal curing.
Continue with stitching and alignment.
FP-1725-B6
Low-temperature curing conductive silver paste, conductive adhesive, suitable for optical communication (PD, MPD, TIA, heat sinks, capacitors, tube sockets) / LED CHIP conductive die bonding / electronic component conductive fixing applications.
Thermal Interface Materials
DOWSIL™ TC-3015
Cure at 60°C, can be reworked after curing, suitable for various interfaces, flexible processing, can be applied by dispensing, screen printing, and stencil printing.
Thermal Interface Materials
DOWSIL™ TC-4525 A/B
Blue, dual-night type RTV, 2.6W/MK thermal gap filling adhesive, soft and easy to rework, contains 180μm glass beads, certification: UL94-V0.
Thermal Interface Materials
DOWSIL™ TC-5351
Gray, single-component thermal paste, with a thermal conductivity of 3.3 W/MK, and excellent stability in filling vertical gaps up to 1MM.
Thermal Interface Materials
52153
Non-silicon thermal insulation sealing material, non-metallic type, high thermal conductivity, thermal conductivity (@36°C): 3.5 W/M.K, with viscosity.
Thermal Interface Materials
53053
Non-silicon thermal insulation sealing material, non-metallic type, high thermal conductivity, thermal conductivity (@36°C): 3.5 W/M.K, with viscosity.
Chip fixed
DOWSIL™ X3-6211
Transparent, single-component, UV quick-curing silicone gel, low viscosity, low stress, resistant to low temperatures (remains soft and elastic gel at -55°C).
Chip fixed
DOWSIL™ ME-1070
Black, single-component, heat-curing silicone rubber, with no by-products during the curing process, has fluidity, low ionic impurity content, and low modulus.
Electromagnetic shielding frame rubber
SP-1000-008-02
Silicone-based RTV single-component conductive adhesive, with EMI shielding >100DB in the frequency range of 1~10GHz.
Electromagnetic shielding frame rubber
FP-1725-R22
PU series RTV single-component conductive adhesive, used on metal or plastic housings, utilizes conductive adhesive strips that resist electromagnetic waves to fill in the uneven surfaces during die casting or molding, providing a highly reliable seal.
Electromagnetic shielding frame rubber
DOWSIL™ EC-6601
Brown, single-component RTV, conductive silicone, electromagnetic shielding effectiveness: 8DB@1 KHZ-8.5 GHZ.
Electromagnetic shielding frame rubber
GS-SG6001A
Room temperature curing / FIPG, suitable for 5G base station modules.
EMI Absorbing Material
FP-IN SERIES (Ink Type)
Ink type for printing, suitable frequency range from 300KHz to 18GHz, applicable for printing on chips or PCB circuit boards, featuring adhesion, wave absorption performance, and other characteristics.
EMI Absorbing Material
RF-5 SERIES (Single Type)
Absorbing sheet material, suitable for frequencies from 1MHz to 10GHz, applicable to various thin electronic devices, protecting circuit board lines from interference by external signals.
Active alignment
EP-28-3410-50K
Single-liquid UV/thermal dual-curing system, low shrinkage, suitable for sealing and bonding materials such as glass, PCB, PA, PEI, metals (AL, FENI alloy), ceramics, etc. in the optoelectronic industry, providing excellent adhesion.
Filling and Packaging
AP-2100-C1(AB)
Two-component, high-temperature fast-curing epoxy resin, featuring excellent handling performance and reliability. Mixing ratio A:B = 10:1; used for secondary reinforcement.
Filling and Packaging
EP-30-BF2
Single-component, high-temperature fast-curing epoxy resin, designed for applications such as optical communication/fiber optics, with excellent operational performance and reliability; used for secondary reinforcement adhesive.
Laser Diode Conductive Bonding
FP-1725-B6
Low-temperature curing conductive silver paste (2.6W/M.K), suitable for optical communication (PD, MPD, TIA, heat sinks, capacitors, tube sockets) / LED CHIP conductive die bonding / electronic component conductive fixing applications.
Laser Diode Conductive Bonding
FP-5300TC-20A
High power high thermal conductivity silver adhesive (>20W/M.K) is used for bonding and curing in optical communication (related to TEC components) and for conductive and thermal applications in electronic components. It is suitable for high power thermal conductive die bonding applications for LEDs above 1W.
Laser Diode Conductive Bonding
ACH35001LV
Thermal conductivity > 15 W/M.K, high TG, solvent-based conductive silver glue, high solid content after curing.
Laser Diode Conductive Bonding
ACH35006
Sintered silver conductive adhesive, thermal conductivity 20W/m.K, curing at 175°C.
Laser Diode Conductive Bonding
TM 150E
High thermal conductivity / low-temperature curing conductive adhesive, thermal conductivity > 60 W/M.K, curing at 150℃.
| Display data rows per page | Search: | |
Rubber material application
|
Product model
|
Feature description
|
| 目前显示第 1 至第 10 个资料列,总计 17 个资料列 | < Previous page Next page> |
Parts are fixed and bonded.
DOWSIL® EA-4100
White, non-flowable, resistant to high and low temperatures, environmentally friendly, good adhesion, certification: UL-94V0.
Parts are fixed and bonded.
DOWSIL® EA-9189
White, non-flowable, resistant to high and low temperatures, environmentally friendly, good adhesion, with a thermal conductivity of 0.8W/mK, certification: UL-94V0.
Parts are fixed and bonded.
UV-SIL® 2001-1
UV (365NM) moisture curing, component fixation reinforcement / high TG point.
IC reinforcement
EPO-SIL® 1382
Four-corner protection, medium viscosity does not flow down, can be used in printing processes and dispensing processes.
IC reinforcement
UV-SIL® 8092
Four-corner protection, high adhesion strength, UV (365NM/405NM).
IC reinforcement
UV-SIL® 2001-1
Four-corner protection, UV (365NM) moisture curing, medium viscosity / high adhesion strength / high TG.
IC reinforcement
JC 823-6
Bottom reinforcement and low-temperature curing can buffer the expansion and contraction stress of solder ball joints when applying underfill to CSP and BGA chips, and can also mitigate the shear force transmission during drop test impacts.
Component Protection
UV-SIL® 8026
UV (365nm), acid-resistant, used for component protection (such as glass, PC, metal), with reworkability that does not damage the substrate.
Component Protection
UV-SIL® 6820-5
UV (365nm), high thixotropy, used for component protection (such as glass, PC, metal), with reworkability that does not damage the substrate.
Component Protection
UV-SIL® 5225-1
UV (365nm), reflow soldering protection, used for component protection (such as glass, PC, metal), with reworkability that does not damage the substrate.
Thermal Interface Materials
THERMAL PAD
Silicone thermal pads, high thermal conductivity, low thermal resistance, customizable for elastic applications, complete size range, certification: UL94-V0.
Thermal Interface Materials
SP-610 SERIES
Silicone thermal pads, high thermal conductivity, low thermal resistance, customizable for elastic applications, complete size range, certification: UL94-V0.
Thermal Interface Materials
DOWSIL™ TC-3015
Pink, single-component curable thermal gel with a thermal conductivity of 1.8 W/MK, suitable for various interfaces, soft and easy to rework, cures at 60°C, automated dispensing, replaces PAD.
Thermal Interface Materials
DOWSIL™ TC-4040
Blue, dual-component curable type, 4 W/mK class gasket, can cure at room temperature after dispensing or can be formed by heating to 40°C as a gap-filling thermal pad, soft and easy to rework.
Thermal Interface Materials
52153
Non-silicon thermal insulation sealing material, non-metallic type, high thermal conductivity, with viscosity, thermal conductivity (@36°C): 3.5 W/m.K.
Thermal Interface Materials
53053
Non-silicon thermal insulation sealing material, non-metallic type, high thermal conductivity, with viscosity, thermal conductivity (@36°C): 3.5 W/m.K.
Electromagnetic wave mask
GS-SG6001A
Room temperature curing / FIPG, this product is suitable for 5G base station modules.
Electromagnetic wave mask
DOWSIL™ EC-6601
Brown, single-component RTV, conductive silicone, electromagnetic shielding effectiveness: 8 dB @ 1 kHz - 8.5 GHz.
EMI Absorbing Material
FP-IN SERIES (Ink Type)
FP-IN SERIES (Ink Type), applicable frequency 300KHZ~18GHZ, suitable for printing on chips or PCB circuit boards, featuring adhesion, wave absorption performance, and other characteristics.
EMI Absorbing Material
RF-5 SERIES (Single Type)
RF-5 SERIES (Sheet Type), absorbing sheet material, suitable frequency 1MHz~10GHz, used in various thin electronic devices to protect circuit board lines from interference by external signals.
Thermal conductive plastic structural components
PC/PP/PA+GF/CF/GRAPHITE
1. Better heat dissipation 1–30W/MK; 2. Can be injection molded - suitable for complex geometries, increasing design flexibility; 3. Lower operating temperature - reduces hotspots, longer service life; 4. Coefficient of thermal expansion - better wear resistance; 5. Can reduce part weight by 50% compared to metals; 6. Inherent corrosion resistance.
Corrosion protection for pipelines
SIL-FC8188AG
Film material, with a thickness of 10um for rapid curing, epoxy resin substrate, suitable for spraying on PCB circuit boards, featuring adhesion, waterproofing, insulation, and resistance to line corrosion and creeping.
Corrosion protection for pipelines
FC 6000
Film material, with a thickness of 10um for rapid curing, acrylic substrate, suitable for spraying on PCB circuit boards, featuring adhesion, waterproofing, insulation, and resistance to creepage corrosion.
| Display data rows per page | Search: | |
Rubber material application
|
Product model
|
Feature description
|
| 目前显示第 1 至第 10 个资料列,总计 17 个资料列 | < Previous page Next page> |
China Kunshan Subsidiary
TEL:+86-512-5778-9977
FAX:+86-512-5778-9944
E-Mail:silmore@silmore.com.cn
Website:http://www.silmore.cn/
Address: 13th Floor, Building 4, Chengbei Lake Commercial Center, 1188 Chengbei Road, Yushan Town, Kunshan City, Jiangsu Province, 215300
China Dongguan Subsidiary
TEL:+86-769-8541-8158
FAX:+86-769-8541-9158
E-Mail:service@silmore.com.cn
Website:http://www.silmore.cn/
Address: No.8 Huafu Road, Shangsha No.6 Industrial Zone, Chang 'an Town, Dongguan City, Guangdong Province, China 523000
COOKIES
Our website uses cookies and similar technologies to personalize the advertising shown to you and to help you get the best experience on our website. For more information, see our Privacy & Cookie Policy
COOKIES
Our website uses cookies and similar technologies to personalize the advertising shown to you and to help you get the best experience on our website. For more information, see our Privacy & Cookie Policy
These cookies are necessary for basic functions such as payment. Standard cookies cannot be turned off and do not store any of your information.
These cookies collect information, such as how many people are using our site or which pages are popular, to help us improve the customer experience. Turning these cookies off will mean we can't collect information to improve your experience.
These cookies enable the website to provide enhanced functionality and personalization. They may be set by us or by third-party providers whose services we have added to our pages. If you do not allow these cookies, some or all of these services may not function properly.
These cookies help us understand what you are interested in so that we can show you relevant advertising on other websites. Turning these cookies off will mean we are unable to show you any personalized advertising.